Atlas launch to test inflatable heat shield - SpaceNews | Canada News Media
Connect with us

Science

Atlas launch to test inflatable heat shield – SpaceNews

Published

 on


WASHINGTON — A payload hitching a ride on the launch of a weather satellite will demonstrate a technology that both NASA is considering for future Mars landings and a company is studying for rocket reusability.

A United Launch Alliance Atlas 5 is scheduled to lift off from Vandenberg Space Force Base in California at 4:25 a.m. Eastern Nov. 10. The primary payload of the rocket is the Joint Polar Satellite System (JPSS) 2 weather satellite, which will be placed in a polar orbit to collect weather data for the National Oceanic and Atmospheric Administration. The launch was previously scheduled for Nov. 1 but postponed to replace a battery in the rocket’s Centaur upper stage.

A secondary payload on the launch of JPSS-2 is Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID), a NASA technology demonstration. While JPSS-2 will be deployed nearly a half-hour after liftoff, LOFTID will remain attached to the Centaur until 75 minutes after liftoff, following a deorbit burn of the Centaur.

Shortly before deployment, LOFTID will inflate a reentry shield six meters in diameter. That heat shield will slow down the vehicle from orbital velocity to Mach 0.7 as instruments on board collect data on the performance of the shield. LOFTID will then deploy parachutes to slow it down for the rest of its descent, splashing down in the Pacific east of Hawaii to be recovered by a ship.

LOFTID is the latest in a series of technology demonstrations by NASA of inflatable reentry systems whose size is not constrained by the payload fairing of the rocket. “Currently, using rigid technologies, we’re limiting the size of the aeroshell itself to fit within the fairing of a launch vehicle,” or no more than about five meters across, said Joe Del Corso, LOFTID project manager at NASA’s Langley Research Center, during a pre-launch briefing in October. That limits the size of payloads delivered to the surface of Mars to about 1.5 metric tons.

A larger aeroshell, using inflatable technology, could enable much heavier payloads, up to the range of 20 to 40 metric tons. “It’s what you need to put humans on Mars,” he said. Larger aeroshells also enable access to higher terrains on Mars where the atmosphere is not dense enough to slow down vehicles with existing systems.

NASA hopes to collect performance on inflatable heat shields with the LOFTID test. John DiNonno, LOFTID chief engineer at NASA Langley, said the heat shield will see peak temperatures in excess of 1,400 degrees Celsius during reentry and experience decelerations of up to 9g. The inflatable structure is protected by a flexible thermal protection system made of materials that can be tailored for the specific mission.

A ship off the coast of Hawaii will recover LOFTID after splashdown, but as a precaution the vehicle will eject data recorders while descending under parachutes that can be recovered separately. It will also return some limited data in real time. “We should be able to get some preliminary feedback within at least a couple hours of reentry on whether it was successful or not,” Del Corso said.

LOFTID cost NASA nearly $93 million over five years, said Trudy Kortes, director of technology demonstrations in NASA’s Space Technology Mission Directorate. NASA is also cooperating with ULA on the mission through an unfunded Space Act Agreement, with ULA supporting integration of LOFTID on the Centaur, as well as the parachute system and recovery ship. The LOFTID mission is formally dedicated to Bernard Kutter, a ULA engineer who worked on advanced technologies but died unexpectedly in 2020.

John Reed, ULA’s chief technologist, said his company is interested in LOFTID as part of the company’s Sensible Modular Autonomous Return Technology (SMART) reusability concept for its Vulcan rocket. Under the SMART approach, the engine section of the Vulcan booster would detach after stage separation and deploy an inflatable aeroshell to slow it during reentry. A parachute would slow the engine section in the final phases of descent.

He said the company is also interested in broader commercial applications of the technology. “The whole focus of this effort has been to develop a path that can support not just us but also LEO commercial applications, returning products from cislunar, as well as getting on to Mars and having the downmass to really enable humanity’s expansion.”

Those future applications will require much larger aeroshells than the six-meter version being tested on LOFTID. At a briefing during the AIAA ASCEND conference Oct. 25, Michelle Munk, acting chief architect at NASA’s Space Technology Mission Directorate, estimated ULA will likely need aeroshells 12 to 14 meters across, while Mars landers may need versions up to 16 meters across.

“We have in our development strategy scaled-up flight tests,” she said, which would also make the inflatable aeroshells more robust and include integrated guidance, navigation and control required for Mars missions.

She added that she expected that any ULA testing of larger inflatable decelerators would support NASA Mars plans. “We’ll get several flights of the hypersonic inflatable aerodynamic decelerator that will be instrumented and give us increased data sets about its performance in the flight environment, which we can use to build confidence and make improvements,” she said.

Those future tests by ULA, she said, will also help sustain vendors that produce key components of inflatable aeroshells that NASA will rely on for future missions. “We see this as a wonderful partnership and a way to maintain the supply chain and keep the learning going as we progress, in the long term, towards a Mars mission.”

Kortes said it’s too early to determine when an inflatable decelerator might be used on a Mars mission. “This is risk reduction,” she said. After LOFTID, “there is a scale-up that we would begin to talk about, begin to work on.”

Adblock test (Why?)



Source link

Continue Reading

News

Here’s how Helene and other storms dumped a whopping 40 trillion gallons of rain on the South

Published

 on

 

More than 40 trillion gallons of rain drenched the Southeast United States in the last week from Hurricane Helene and a run-of-the-mill rainstorm that sloshed in ahead of it — an unheard of amount of water that has stunned experts.

That’s enough to fill the Dallas Cowboys’ stadium 51,000 times, or Lake Tahoe just once. If it was concentrated just on the state of North Carolina that much water would be 3.5 feet deep (more than 1 meter). It’s enough to fill more than 60 million Olympic-size swimming pools.

“That’s an astronomical amount of precipitation,” said Ed Clark, head of the National Oceanic and Atmospheric Administration’s National Water Center in Tuscaloosa, Alabama. “I have not seen something in my 25 years of working at the weather service that is this geographically large of an extent and the sheer volume of water that fell from the sky.”

The flood damage from the rain is apocalyptic, meteorologists said. More than 100 people are dead, according to officials.

Private meteorologist Ryan Maue, a former NOAA chief scientist, calculated the amount of rain, using precipitation measurements made in 2.5-mile-by-2.5 mile grids as measured by satellites and ground observations. He came up with 40 trillion gallons through Sunday for the eastern United States, with 20 trillion gallons of that hitting just Georgia, Tennessee, the Carolinas and Florida from Hurricane Helene.

Clark did the calculations independently and said the 40 trillion gallon figure (151 trillion liters) is about right and, if anything, conservative. Maue said maybe 1 to 2 trillion more gallons of rain had fallen, much if it in Virginia, since his calculations.

Clark, who spends much of his work on issues of shrinking western water supplies, said to put the amount of rain in perspective, it’s more than twice the combined amount of water stored by two key Colorado River basin reservoirs: Lake Powell and Lake Mead.

Several meteorologists said this was a combination of two, maybe three storm systems. Before Helene struck, rain had fallen heavily for days because a low pressure system had “cut off” from the jet stream — which moves weather systems along west to east — and stalled over the Southeast. That funneled plenty of warm water from the Gulf of Mexico. And a storm that fell just short of named status parked along North Carolina’s Atlantic coast, dumping as much as 20 inches of rain, said North Carolina state climatologist Kathie Dello.

Then add Helene, one of the largest storms in the last couple decades and one that held plenty of rain because it was young and moved fast before it hit the Appalachians, said University of Albany hurricane expert Kristen Corbosiero.

“It was not just a perfect storm, but it was a combination of multiple storms that that led to the enormous amount of rain,” Maue said. “That collected at high elevation, we’re talking 3,000 to 6000 feet. And when you drop trillions of gallons on a mountain, that has to go down.”

The fact that these storms hit the mountains made everything worse, and not just because of runoff. The interaction between the mountains and the storm systems wrings more moisture out of the air, Clark, Maue and Corbosiero said.

North Carolina weather officials said their top measurement total was 31.33 inches in the tiny town of Busick. Mount Mitchell also got more than 2 feet of rainfall.

Before 2017’s Hurricane Harvey, “I said to our colleagues, you know, I never thought in my career that we would measure rainfall in feet,” Clark said. “And after Harvey, Florence, the more isolated events in eastern Kentucky, portions of South Dakota. We’re seeing events year in and year out where we are measuring rainfall in feet.”

Storms are getting wetter as the climate change s, said Corbosiero and Dello. A basic law of physics says the air holds nearly 4% more moisture for every degree Fahrenheit warmer (7% for every degree Celsius) and the world has warmed more than 2 degrees (1.2 degrees Celsius) since pre-industrial times.

Corbosiero said meteorologists are vigorously debating how much of Helene is due to worsening climate change and how much is random.

For Dello, the “fingerprints of climate change” were clear.

“We’ve seen tropical storm impacts in western North Carolina. But these storms are wetter and these storms are warmer. And there would have been a time when a tropical storm would have been heading toward North Carolina and would have caused some rain and some damage, but not apocalyptic destruction. ”

___

Follow AP’s climate coverage at https://apnews.com/hub/climate

___

Follow Seth Borenstein on Twitter at @borenbears

___

Associated Press climate and environmental coverage receives support from several private foundations. See more about AP’s climate initiative here. The AP is solely responsible for all content.

Source link

Continue Reading

Science

‘Big Sam’: Paleontologists unearth giant skull of Pachyrhinosaurus in Alberta

Published

 on

 

It’s a dinosaur that roamed Alberta’s badlands more than 70 million years ago, sporting a big, bumpy, bony head the size of a baby elephant.

On Wednesday, paleontologists near Grande Prairie pulled its 272-kilogram skull from the ground.

They call it “Big Sam.”

The adult Pachyrhinosaurus is the second plant-eating dinosaur to be unearthed from a dense bonebed belonging to a herd that died together on the edge of a valley that now sits 450 kilometres northwest of Edmonton.

It didn’t die alone.

“We have hundreds of juvenile bones in the bonebed, so we know that there are many babies and some adults among all of the big adults,” Emily Bamforth, a paleontologist with the nearby Philip J. Currie Dinosaur Museum, said in an interview on the way to the dig site.

She described the horned Pachyrhinosaurus as “the smaller, older cousin of the triceratops.”

“This species of dinosaur is endemic to the Grand Prairie area, so it’s found here and nowhere else in the world. They are … kind of about the size of an Indian elephant and a rhino,” she added.

The head alone, she said, is about the size of a baby elephant.

The discovery was a long time coming.

The bonebed was first discovered by a high school teacher out for a walk about 50 years ago. It took the teacher a decade to get anyone from southern Alberta to come to take a look.

“At the time, sort of in the ’70s and ’80s, paleontology in northern Alberta was virtually unknown,” said Bamforth.

When paleontogists eventually got to the site, Bamforth said, they learned “it’s actually one of the densest dinosaur bonebeds in North America.”

“It contains about 100 to 300 bones per square metre,” she said.

Paleontologists have been at the site sporadically ever since, combing through bones belonging to turtles, dinosaurs and lizards. Sixteen years ago, they discovered a large skull of an approximately 30-year-old Pachyrhinosaurus, which is now at the museum.

About a year ago, they found the second adult: Big Sam.

Bamforth said both dinosaurs are believed to have been the elders in the herd.

“Their distinguishing feature is that, instead of having a horn on their nose like a triceratops, they had this big, bony bump called a boss. And they have big, bony bumps over their eyes as well,” she said.

“It makes them look a little strange. It’s the one dinosaur that if you find it, it’s the only possible thing it can be.”

The genders of the two adults are unknown.

Bamforth said the extraction was difficult because Big Sam was intertwined in a cluster of about 300 other bones.

The skull was found upside down, “as if the animal was lying on its back,” but was well preserved, she said.

She said the excavation process involved putting plaster on the skull and wooden planks around if for stability. From there, it was lifted out — very carefully — with a crane, and was to be shipped on a trolley to the museum for study.

“I have extracted skulls in the past. This is probably the biggest one I’ve ever done though,” said Bamforth.

“It’s pretty exciting.”

This report by The Canadian Press was first published Sept. 25, 2024.

The Canadian Press. All rights reserved.

Source link

Continue Reading

News

The ancient jar smashed by a 4-year-old is back on display at an Israeli museum after repair

Published

 on

 

TEL AVIV, Israel (AP) — A rare Bronze-Era jar accidentally smashed by a 4-year-old visiting a museum was back on display Wednesday after restoration experts were able to carefully piece the artifact back together.

Last month, a family from northern Israel was visiting the museum when their youngest son tipped over the jar, which smashed into pieces.

Alex Geller, the boy’s father, said his son — the youngest of three — is exceptionally curious, and that the moment he heard the crash, “please let that not be my child” was the first thought that raced through his head.

The jar has been on display at the Hecht Museum in Haifa for 35 years. It was one of the only containers of its size and from that period still complete when it was discovered.

The Bronze Age jar is one of many artifacts exhibited out in the open, part of the Hecht Museum’s vision of letting visitors explore history without glass barriers, said Inbal Rivlin, the director of the museum, which is associated with Haifa University in northern Israel.

It was likely used to hold wine or oil, and dates back to between 2200 and 1500 B.C.

Rivlin and the museum decided to turn the moment, which captured international attention, into a teaching moment, inviting the Geller family back for a special visit and hands-on activity to illustrate the restoration process.

Rivlin added that the incident provided a welcome distraction from the ongoing war in Gaza. “Well, he’s just a kid. So I think that somehow it touches the heart of the people in Israel and around the world,“ said Rivlin.

Roee Shafir, a restoration expert at the museum, said the repairs would be fairly simple, as the pieces were from a single, complete jar. Archaeologists often face the more daunting task of sifting through piles of shards from multiple objects and trying to piece them together.

Experts used 3D technology, hi-resolution videos, and special glue to painstakingly reconstruct the large jar.

Less than two weeks after it broke, the jar went back on display at the museum. The gluing process left small hairline cracks, and a few pieces are missing, but the jar’s impressive size remains.

The only noticeable difference in the exhibit was a new sign reading “please don’t touch.”

The Canadian Press. All rights reserved.

Source link

Continue Reading

Trending

Exit mobile version